![3beltwesty](/img/default-banner.jpg)
- Видео 1 766
- Просмотров 8 574 233
3beltwesty
США
Добавлен 27 окт 2006
3458A TURN DISPLAY OFF with DISP 2 command
Turning most of the Display off with Front panel commands. ie DISP then 2 key then Enter key
Просмотров: 72
Видео
3458 Drift Test A9 Board LTZ1000 CRUDE ACAL
Просмотров 532 месяца назад
After ACALS the 3458A under test reads close to references. The unit drifts and CAL? 72 commands show the A value has a 37 ppm per day drift. The correct test is 7 days with App note 18. Still running the test now
3458A A3 Board Drift and B17 radio room ball turret
Просмотров 352 месяца назад
3458A reads correct after ACAL but drifts due to bad A3 DAC board
Hardman Red double bubble repair plastic 3028 Transfer switch
Просмотров 723 месяца назад
Engineering grade Epoxy repair of crack in Circuit breaker lug support. Boss was cracked so lacked some support. Repair is to just make the lug support more robust. It is probably more robust now than the original. This was not a safety issue. Hardman Red Double Epoxy I have used for many decades in prototyping work. It has little shrinkage. The meters on this unit say watts but they really are...
Piggly Wiggly eggs cooking with gas
Просмотров 6113 месяца назад
Shot eons ago with 240 fps casio camera
Carpenter Bees take out wooden rake
Просмотров 603 месяца назад
Carpenter Bees take out another wooden handle garden tool. Horizontal 10mm Diameter hole then Vertical hole.
8 inches Rain Gauge too small 5 gallon bucket winner
Просмотров 713 месяца назад
South Miss rain May 13th 2024 was 8 inches. The 5 inch gauge overflowed. The homemade 10 inch gauge needs to be rebuilt. It failed in the last hurricane. :) 3BW S22U 11K
Incredible Edger Mounting skate sharpener vs Old 1978 Iceskate version
Просмотров 743 месяца назад
The 1978 "The iceskate sharpener" has 1 track bar and a tall carriage. This reduces the tilt error due to the side profile's curve. The unit 2? decades later has 2 track bars and no error plus has 3 different carriages. The original unit has US patent 4109419 marked on it. Both have fine tooling. The Aluminum castings are probably A356. I goofed in the video and one place said cast iron. patent...
LED Add pull cord to ancient Incandescent fixture
Просмотров 463 месяца назад
Intermittently used fixture is 12 ft high in the old shop. Once had 200 watt 130 Volt reddish color output (2500K? ) Edison bulbs that put out little UV light for handing UV sensitive materials.. These were hot as heck. After this process was gone the fixture got CFL bulbs; we used the "regular looking" non Curlique variants so the string wound not foul on the bulbs. This is the a replacement o...
Incinolet Power wattmeter tester digital meter inline 120 volts
Просмотров 483 месяца назад
Inline 120 volt temporary power tester. Has 10 guage cord; male and female 20 amp 120 volt connectors. This is a temporary tester that goes between the Incinolet cord and the 20 amp 120 volt wall socket. This tester has a current transformer that measures the current. The two sense wires connect to another 120 volt socket. I built this because a loose connection in this old incinolet acted like...
What Language is this sound like? Reversed Video mistake
Просмотров 1153 месяца назад
What language does reverse English sound like. Editing goof I uploaded 3BW S22U 8K
1956 Westinghouse Wattmeter Type DA 120 volt on Refrigerator
Просмотров 443 месяца назад
1956 Wattmeter used on a 1972 Sears Kenmore Refrigerator. This DA series meter is 120 volts 15 amps with a 4X overload rating. So it was used for 120 volt 60 amp service when new. The Kh factor is 1.8 This meter was bought from watt meter man at the TRW swap meet in 1996 for 5 dollars. The Sears refrigerator is 6.6 Cubit feet and uses R12 Freon. It uses less energy than any replacement sized un...
1948 SANGAMO JA Watthour meter in 120 volt AC service
Просмотров 373 месяца назад
SANGAMO Type JA 240 volt watthour meter used on 120 volts. This was bought from the meter man at the TRW ham swap meet in 1995 for 5 dollars. This is an "A" type meter; ie non socketed. This is a 15 amp 240 volts meter with a 4X overload rating. So was used on a late 1940's house or apartment with a 60 Amp 240 Volt service in Southern California. This meter has been connected in a Barn since Bi...
AUTO SHACK Antifreeze and sparkplug wires
Просмотров 183 месяца назад
Auto Shack automotive stuff. S22U 3BW 8K
SANGAMO Watthour meter Reset Type F Portable electric
Просмотров 543 месяца назад
To Reset the bezel is removed and the dial is rotated back to Zero. This meter was built in 1935. It is rated at 5 amp 115 Volts AC. These were used to test small equipment and also in plating processes. S22 8K 3BW
Hockey Puck vs AMROC Hybrid Rocket Fuel Polybutadiene Density
Просмотров 193 месяца назад
Hockey Puck vs AMROC Hybrid Rocket Fuel Polybutadiene Density
FLUKE 2176A Zero Adjust C18 location RJD/Operate switch
Просмотров 273 месяца назад
FLUKE 2176A Zero Adjust C18 location RJD/Operate switch
FLUKE 2176A Digital Thermometer Part 4-33 ZERO Adjustment
Просмотров 263 месяца назад
FLUKE 2176A Digital Thermometer Part 4-33 ZERO Adjustment
Generator DC connector FIRMAN WH03242
Просмотров 1284 месяца назад
Generator DC connector FIRMAN WH03242
LED BULB Flickers after storm power glitch
Просмотров 454 месяца назад
LED BULB Flickers after storm power glitch
VEVOR SV-2000VA Voltage Converter Adjust meters Toroid Transformer
Просмотров 9604 месяца назад
VEVOR SV-2000VA Voltage Converter Adjust meters Toroid Transformer
Mini Spilt leaks Water when in Heat Pump mode
Просмотров 515 месяцев назад
Mini Spilt leaks Water when in Heat Pump mode
FIRMAN WH03242 Propane First startup Generator
Просмотров 2,7 тыс.5 месяцев назад
FIRMAN WH03242 Propane First startup Generator
FIRMAN WH03242 Test Battery drain current
Просмотров 1815 месяцев назад
FIRMAN WH03242 Test Battery drain current
Biloxi Hockey Ice 1 inch thick minus 7 C
Просмотров 1807 месяцев назад
Biloxi Hockey Ice 1 inch thick minus 7 C
Need RMA for Sparx Bad 5/16 ring Order 202261 delivered Jan 10 2024
Просмотров 697 месяцев назад
Need RMA for Sparx Bad 5/16 ring Order 202261 delivered Jan 10 2024
Water Faucet Freeze protection Homemade
Просмотров 1557 месяцев назад
Water Faucet Freeze protection Homemade
NEW Defective SPARX 5/8 inch GRIND DISK needs a RMA skate sharpener
Просмотров 1367 месяцев назад
NEW Defective SPARX 5/8 inch GRIND DISK needs a RMA skate sharpener
Mississippi Seawolves pregame entry Nov 18 2023
Просмотров 668 месяцев назад
Mississippi Seawolves pregame entry Nov 18 2023
Goalie Ice Skates Radius of Hollow vs Blade Thickness
Просмотров 1659 месяцев назад
Goalie Ice Skates Radius of Hollow vs Blade Thickness
It moves, it MOVED -- signs of life!!
My printer Brother MFC 7820N I flowing your instruction I can't reset replace new drum and tonerplease every time power on it show "change drum soon" and unable printing help?
Wm2501hwa, the hva is a darker color, hwa is white
Must videos skip this ..
Thanke you! Hi from Russia 💪✊🤝
It has to leak unless u apply sealant.
Secomd(wait two years to say 3rd)
Thanks
Very well done analysis, sir! I’m a factory certified tech/trainer for Mitsubishi and Fujitsu VRF. I would love to do what you’ve done in my training lab with multiple types of units one day. The hardest part, and the reason why you’ll go in circles on your reading sometimes, is there is about 6-10 temps/pressures the unit is constantly reading and adjusting to. They do have targets for SH, Condensing Temp, Evap Temp, SC, Tube-in-Tube SC, but that target can be affected based on compressor speed, compressor discharge temp, outdoor temps, etc. These targets are mostly proprietary and not published. Aside from being proprietary, it’s just too hard for the manufacturers to publish reading for all types of conditions. That’s why if there’s ever a question of charge, dump it and weigh it in. One thing you might want to look into is a Service Tool/Maintenance tool for your brand. You will be able see some targets and actual indoor and outdoor coil temps, compressor speed/amps, LEV positions, etc. This is especially helpful if you are using multizone systems. My next project in my lab is to run through common field scenarios and record all these reading so you can see how the system will react to an overcharge, under charge/leak, dirty filters, blower wheel, restrictions, etc. One of the hardest parts about diagnosing these units is they will try to run as best as possible no matter what is going on. As far as evap coil temps in cooling, most target 35-50* and super heat can be as low as 1-5* depending on conditions. LEV’s are far superior of mechanics TXV’s due to their immediate response to changes. Loved your video, would like to see more of your work and analysis!
That unit is an off brand a Superair. If you google the part numbers on the inside condensor parts you get that the BOX is used by Carrier; Meida? etc Then I used that to download several difference service manuals. The local area here is hot and humid. So I purposely run a small 9000 BTUH unit all the time to pull the moisture out. The unit in the video has several different temp sensors in the outside box. The CPU decides what outside blower speed based on these and other stuff. If the inside set point is 65C and it is 80F F and 95 RH out the fan will not go to full rpm until the outside air temp rises, ie will run full tilt at 90F outside 35 years ago when in Singapore; Thailand and Japan they had mini splits with R22 and the expansion valve was in the INSIDE unit then. This added some noise sometimes. But there were 2 Hi Low pressure service ports on these. An R22 5 ton split system I have here has TXVs; two since was once 2 5 ton coils; two 5 ton condensors.
Good lord, how many times can you say the same thing?
About all RUclips questions ask what is mentioned many times already on the videos. So that is why things are mentioned several times. The average RUclips viewer just surfs videos and then asks a question that is already mentioned FIVE times and the Title has it too. SO maybe you should spend your life answering questions for free too. lol So like on this video folks have asked what Canon model it is about when it is in the title "Canon IPF 750" That is why call centers are overseas too; folks have a less understanding of basics; ie reading.
Can you do a video on the 220 connector I tested the 220v port and from each line 1 & line 2 to neutral I've got 170 on line 1 and 70 volts on line 2... can you see if yours does the same thing and if so how come it's not clean power if I connect both my tester leads to line 1 and line 2 my meter shows 240
9 ft is too flat
Where is the replaceable glass fuse at?
Thank you very informative. I have a hard jam in my pfaff 130-6 not seized from lack of lubrication felt like a needle broke and was inside. there is no needle but I can see with a magnifying glass wrapped brass thread but thinner. Cannot move the handwheel more than 1/8th of an inch. the wire is below the case holder part right around the post that holds in the hook holder. Thanks again learned lots
Are you finding a trend of Sparx users’ steel with uneven grinding? For example, I’m seeing either too much toe or heel blade taken off compared to other end of steel. I don’t have a Sparx but I find myself correctly the imbalance.
You better re train your crew buddy.
That's highway 45 almost to the town I live
Great explanation but you left out adjusting it. The adjustment screw is under that brass threaded cap.
Is it harmful? I’m kinda scared
nah theyre completely harmless and actually pretty friendly, theyre great pollinators too important for the environment
Oh…
You bent up the injectors
Couldn't you drop the idler pulley lower ? i'm replacing motor on mine right now
I ended up just cutting the shaft off the engine "Original engine has 2 7/16 long crankshaft. Harbor Freight has 3 5/32 inch shaft. Difference is 23/32 inch or about 0.72 inch" ruclips.net/video/s-DRP3vZTz0/видео.html The video link shows cutting the shaft 7/10 inch shorter ; 18mm shorter The stock engine on mine has a short shaft so an actual direct fit engine was double the price of the HF engine I Farted around trying hack saw blades; saws zall ; then the cutt off wheel was what worked That HF engine I used has a brake ie flywheel brake. My Ariens string trim mower does not. So I had to pull one the HF engine brake with a coast hanger wire
Harbor freight makes the 5 ton unit. Wen makes the 6.5 ton unit, and Bilt Hard has a 6.5 ton unit for all the same price and all have fairly good reviews. I's still deciding which one I'll buy? I pretty much ruled out Harbor Freights splitter because it's just rated at 5 ton, and the other two are both 6.5 ton units. For about $35 more the Wen will include a stand, but it looks kinda flimsy and not rated all that well, so I will probably make my own stand for which ever splitter I buy.
Excelente demostración. Muchas gracias
Thanks
I bought several different VA sizes of these to test and got busy. So someday I will test them for no load loss; efficiency etc. I have acquired a 240 volt variac with headroom to test them. ie core loss versus voltage etc
I can't hear you. Why are you taking so low ? It may be a good video. Who knows?
"lifetime warranty"
Bro got 96p
Cellular South weird swivel phone. Flagship phone for 2004. www.phonescoop.com/phones/phone.php?p=486 They were like 450 bucks at 1st; 339 by late 2004 outright is cash. When bundled with a cell service funny money and maybe just 250 The 1.2 Megapixel "camera" is listed as 1. 1.2; 1.3 etc. My tests are more like a VGA 480x640 sensor and upsized for marketing. Got in many arguments with old fossil folks of all ages. ie "a cell phone will never replace a camera"
Hello doing this on an 89 ranger does the balancer need to be flush against the engine or is there a gap
Lol, at school at the bus station, a hoverfly landed on me and my classmate was like "There's a wasp on your hand!" But i didn't get scared, cuz i knew that was a hoverfly and it isn't dangerous
The give out scary wasp like noise. I tend to see them when working on cutting wood out in the woods. or sawing lumber. That video here I was working on my roof.
They're completely harmless as you probably already know by now. I found some chilling in a couple areas in Scotland, got a couple to land on my hand, they seem smart, almost like they're some kind of drone. Probably my favourite insect
@@TheLutherRed The seem to be attracted to when I am workling with wood. Loggers in the South West USA call them "news bees" since the legend is they bring one the good news of the day! They sure have a cool way to scare you if you think they will sting.
The first shop on the left called longs auto shop. That’s my uncle and great uncles shop.
@@Monroemanordogs that I'd really cool.. I purposely shot this since had not been through Quitman in decades.. I was earlier in Tupelo then was at Mississippi State and drove south on us 45. Then on a total lark decision deciding to not get on I 59 yet. Above Quitman that day there was a fire below Meridian on the roadside fields. When I left Quitman that day I drove West and got into a mess of Kuduz before got to us 11.. so got sort of sidetracked but did not know that Kuduz was like a jungle there. Regards
@@3beltwesty man kudzu is evil Incarnate lol about the only thing to stop it are goats. I haven’t been in quitman since around 2009 2010 or so. I actually lived down the street that you loop down off Main Street there by the police station lol 😂 I was born in meridian. Did you know rogue from X-men was also born there! Fun fact!
My home Town. It’s okay.
Why would you not have the machine profile to the Two dots instead of the shorter Three dots and then have to blend afterwards. This does not make sense to me. What is this reason?
whats the size of the cutting wheel for the 2A model? i cant find information about it.
That looks like an easy weld. IF you want to fix it without the weld I'd use JB weld epoxy. Then do the band clamp around it. That copper band was a smart choice.
Nice demonstration. Waste spark is when you have 1 coil for 2 different cylinders, it fires 1 plug on compression stroke but the other fires on exhaust stroke hence the "wasted spark". It doesn't have anything to do with cleaner burning or firing twice
My dad has one in working order. Only worth wath you can get for it.
Is it just experience and care that stops you gouging out a dent in the blade as it passes, or is that by some mysterious quirk actually quite hard to make happen?
thank you for sharing the video. I had Sparx 2.0 for almost a year and still not entirely sure if I got the alignment right since depending on the angle at which I stare into lens it changes the angle making it difficult to see if the alignment ring and the little knob are really aligned or not :( Is there any trick to ensure they are?
Good video . 73
I replaced the evaporator fan and plugged the refrigerator back in but the fan isn’t spinning. Do I need to wait with it plugged in and on before it will start working again? We don’t have an icemaker on ours
On that unit in the video the evaporator fan and condenser fan 'RUN" when the compressor runs. ie wired in parallel. The temperature control (thermostat) clicks on and those 3 items all run. The schematic on that unit as a pdf file is downloadable if you Google : "197D8122P002" documents.cdn.ifixit.com/IxYbtI6jQiXlSvr2.pdf So on this videos unit the Evaporator runs when the Compressor runs.
You can always use a hair dryer to melt the ice faster, & it blows the water off anything.
Hi thank you for such great information. I have a lot of questions about this machine, I am about to buy one second hand. Any way I can reach out to you about the questions I have?
Where did you buy this?
I bought it from Prosharp. Before they got bought by Bauer.. should should bug Bauer's Prosharp division and ask them to bring them back
wwwwowwwww
0:02 this is an LG true stream
1 minute ago what size tool is needed to remove brake lines
what sixe tool is need to remove brake lines
Has the floating neutral caused you any issue / concern???!
Urine has salts which will rust steel. Outdoors has a lot of animals; it's not complicated. Birds piss too.
Hi! It is possible to put the 246v down to 220v?
As is No; Since the transformer is wound to go Up or Down by 2. Winding is tapped so the turns ratio is 2 so fixed. If one wanted to input 246 V and get 220 volts out you have to add a tap ie winding place for the 220 volts- You can get a 240 volt variac and set it to 220 volts too regards